RC Radios, Transmitters, Receivers, Servos, gyros Discussion all about rc radios, transmitters, receivers, servos, etc.

hitec 05s micro receiver and futaba radio

Old 07-05-2011, 02:36 AM
  #1  
andyrew
New Member
Thread Starter
 
Join Date: Jul 2011
Posts: 2
Default hitec 05s micro receiver and futaba radio

hi all,
i have 2 hitec 05s micro receivers that i am trying to use with my planes and a futaba 9z and futaba 8uap, both using synthesizer modules (one futaba, one hitec).

for some reason i cannot get either radio to work correctly with the receivers. they are on the correct channel, they are in ppm mode and they are transmitting. every now and then when i power up the planes, the radios will control them correctly. mostly the servos just all go nuts and the channels dont match up correctly (suddenly the ailerons are on the elevator stick, etc).

anyone know what might be causing this? is there an issue where these receivers just don't work with futaba radios? or am i going to have the same issue with a futaba receiver? i have tried everything and just can't figure it out.

thanks,
andy
andyrew is offline  
Old 07-05-2011, 09:17 AM
  #2  
slipstick
Super Contributor
 
Join Date: Oct 2005
Location: N.Staffs, UK
Posts: 2,350
Default

Where are you and what frequency band are you using ?

Those receivers normally work fine with Futaba Txs. Do you have the correct Hitec crystals in the Rxs ?

Do the Txs work correctly with any other Rxs ? That's surely the first thing to check. I've heard of some initialisation problems with the 9Z modules though mainly when used with Berg Rxs. And of course the Hitec Spectra module isn't designed to be used in a Futaba Tx so if it ever did work that would just be good luck (and if you're in the US on 72MHz it's technically illegal to use a module from a different manufacturer in a Tx).

Steve
slipstick is offline  
Old 07-05-2011, 01:07 PM
  #3  
andyrew
New Member
Thread Starter
 
Join Date: Jul 2011
Posts: 2
Default

both tx's work fine with every other receiver. i've never had an issue until these two.

i did some research and found some dealer that said they aren't compatible with a 9z if you're using the synth module. i don't know if that's true or not, but so far, he's right as for the other one, i don't know why it won't work.

as far as the crystals... that one i don't know. i don't know if they're hitec or not. i bought them as a flight pack from tower and had the xtal included. i can only assume they sent me what should have been the correct crystal. but on the xtal label i can't tell what it is. it's just got a channel # and freq. i can't see anywhere where it tells me a brand or if it's single or dual conversion. does it need to be specifically made by hitec?
andyrew is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
bryris
Radio Equipment For Sale & WTB
1
06-12-2011 05:58 AM
RCFlyer44
Power Systems
22
03-29-2011 05:55 AM
bob4432
RC Radios, Transmitters, Receivers, Servos, gyros
26
01-03-2011 11:43 AM
Zocane
General Electric Discussions
3
12-27-2010 10:25 PM
All American
Radio Equipment For Sale & WTB
0
07-02-2010 05:47 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: hitec 05s micro receiver and futaba radio


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.06413 seconds with 13 queries