novice needs help with a Turnigy 3530 1100 - WattFlyer RC Electric Flight Forums - Discuss radio control eflight

Brushless Motor Construction Discuss design and construction of custom Brushless motors

novice needs help with a Turnigy 3530 1100

Old 08-31-2011, 11:56 PM
  #1  
postie
postie
Thread Starter
 
Join Date: Aug 2011
Location: Hanover ontario canada
Posts: 1
Wink novice needs help with a Turnigy 3530 1100

hi...this is my problem...how to reverse the shaft on a C3530-1100 to fly in a multiplex fun cub???
when holding the motor the lettering in right side up and shaft is coming out of top of the motor .... I want it out the bottom
How do I decide which wire colours line up on the ECS???

yes I am a novice .... sure hope some will have the time to help me
postie
postie is offline  
Old 09-01-2011, 05:07 AM
  #2  
ron_van_sommeren
homo ludens modelisticus
 
ron_van_sommeren's Avatar
 
Join Date: Jul 2005
Location: near Nijmegen, Nederland
Posts: 1,158
Default

www.innov8tivedesigns.com
-> howto videos
-> exchanging a shaft
ron_van_sommeren is offline  
Old 09-01-2011, 05:26 AM
  #3  
cyclingsarge
Member
 
cyclingsarge's Avatar
 
Join Date: Oct 2007
Location: Cadiz, KY
Posts: 47
Default

I have a fun cub and I am trying to figure what why u need to do that? How about a picture for clarity.
cyclingsarge is offline  
Old 09-01-2011, 06:51 AM
  #4  
JetPlaneFlyer
Super Contributor
 
JetPlaneFlyer's Avatar
 
Join Date: Mar 2009
Location: Aberdeen, Scotland
Posts: 6,121
Default

Also puzzled why you would need to do that unless the motor was incorrectly assembled by the factory (unlikely)

Forget the writing, that's just a sticker which could be stuck on either way.. The end of the motor that the wires go into is the fixed end. The motor shaft should normally stick out of that same end.

Like in the photo here (ignore writing, look at the wires): http://www.hobbyking.com/hobbyking/s...AXi_2808_.html

If you want to mount the prop on the opposite end to where the shaft sticks out then the motor comes with a prop adapter that bolts to the rotating end of the motor... The shaft would then just stick through a hole in the firewall/mount.

As for the wires.. just connect them any way you like.. If the motor runs backward swap over any two and direction will be reversed.

Steve
JetPlaneFlyer is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
CHELLIE
Hi-Performance and Sailplanes
2016
05-28-2020 09:50 PM
steinar
Brushless Motor Construction
17
09-23-2011 06:21 PM
mcav8tr
Power Systems
7
08-19-2011 04:36 PM
pl365322
Power Systems
12
07-04-2011 07:41 PM
terrynshed
Motors and Speed Controllers for sale & WTB
0
12-28-2010 08:46 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: novice needs help with a Turnigy 3530 1100


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.10036 seconds with 15 queries