General Electric Discussions Talk about topics related to e-powered RC flying

servo interacting with others

Old 09-23-2021, 11:58 PM
  #1  
Ken
New Member
Thread Starter
 
Join Date: Jan 2007
Posts: 4
Default servo interacting with others

I have a Timber X with many flights until my last flight took off ailerons went hard right into ground. After testing I noticed when I give full up elevator the ailerons go full right . Does this sound like servo problems or receiver problems?? Please help it will be greatly appreciated. Thanks Ken
Ken is offline  
Old 09-24-2021, 04:29 AM
  #2  
firemanbill
Community Moderator
 
firemanbill's Avatar
 
Join Date: Sep 2005
Location: Sevierville, Tennessee
Posts: 20,747
Default

could be in the transmitter. Have you changed anything in the setup? Mixing the two channels at 100% will do it. could be Rx failing as well. if you have another receiver try it and see if it still does it. Also check that you didn't inadvertently plug the elevator servo into one of the aileron wye leads.

Just a few quick thoughts
firemanbill is offline  
Old 09-24-2021, 10:33 AM
  #3  
solentlife
Super Contributor
 
solentlife's Avatar
 
Join Date: Oct 2010
Location: Ex UK Brit now in Latvia west coast - Ventspils
Posts: 12,766
Default

If the aileron servos are on a Y lead ... its possible that Y lead is at fault ...

Test by removing one servo and operate stick .. check it works correct ... unplug that one and reconnect other servo in its original lead side and check ... then if both OK - have both plugged in and check ...

Its not unknown for Y leads to fail ......

If servos and Y lead give no clue ... try the Y lead in another RX channel ... see what happens (means of course different stick to operate !).... its just to see if its RX ch at fault.
solentlife is online now  
Old 09-24-2021, 01:17 PM
  #4  
quorneng
Super Contributor
 
quorneng's Avatar
 
Join Date: Jul 2008
Location: Cheshire, UK
Posts: 2,018
Default

Don't assume it is a servo or receiver problem. It may be but the servos are controlled by the transmitter..
As suggested use another receiver and servos and see if the problem is duplicated. If it is you know the issue is with the transmitter. If there is no problem then you know it is either the receiver, the wiring or servos themselves.
Remove the receiver and connect it to some good servos. If no problem than you are down to a problem with the wiring or those particular servos.
'Logical substitution' is really the only way to diagnose such without access to sophisticated test gear.

Last edited by quorneng; 09-24-2021 at 08:09 PM.
quorneng is offline  
Old 09-24-2021, 08:24 PM
  #5  
Ken
New Member
Thread Starter
 
Join Date: Jan 2007
Posts: 4
Default

Than you great info....Ken
Ken is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
x-nitro
3D Flying
16
02-25-2016 02:58 PM
kyleservicetech
RC Radios, Transmitters, Receivers, Servos, gyros
10
12-02-2014 07:48 AM
k-vette
RC Radios, Transmitters, Receivers, Servos, gyros
9
02-06-2012 01:13 PM
RCFlyer44
Power Systems
22
03-29-2011 04:55 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: servo interacting with others


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.10712 seconds with 12 queries