WattFlyer RC Electric Flight Forums - Discuss radio control eflight - Search Results

Search: Posts Made By: dopey190
Showing results 1 to 13 of 13
Search took 0.00 seconds.
05-08-2013, 03:26 AM
Replies: 8
Views: 3,259
Posted By dopey190

Well I went ahead and ordered another motor. As...

Well I went ahead and ordered another motor. As from whats been said today, it doesnt look like it will be worth a try. Lesson learned. Thank you guys.
05-08-2013, 01:19 AM
Replies: 8
Views: 3,259
Posted By dopey190

Ok ill try it. I didnt know if anything was...

Ok ill try it. I didnt know if anything was holdint the magnets on the back half. I had pulled the shaft out cause it was loose, and I was curious in case I had to replace it. Thanks
05-08-2013, 12:58 AM
Replies: 8
Views: 3,259
Posted By dopey190

168765Took the shaft out and the front that...

168765Took the shaft out and the front that spins, whats left is the magnets and the back of the motor where the mount attaches, underneath all of this is where the wires come out. I noticed the...
05-08-2013, 12:23 AM
Replies: 8
Views: 3,259
Posted By dopey190

Outrunner Eflite 480 brushless

Outrunner Eflite 480 brushless
05-07-2013, 11:48 PM
Replies: 8
Views: 3,259
Posted By dopey190

Repairing wires on Eflite 480

The shaft on my 480 was loose, after tightening the screws, I noticed I had pulled the middle wire out. How do I take the magnets off so I can solder the dam wire back on? It was easy to remove the...
04-18-2013, 10:35 PM
Replies: 30
Views: 5,069
Posted By dopey190

"Getting irritated at young kids and old kids is...

"Getting irritated at young kids and old kids is a symptom of spending too much valuable time on these forums instead of building and/or flying."

Where I was getting at with my initial response. ...
04-16-2013, 11:30 PM
Replies: 30
Views: 5,069
Posted By dopey190

Why dont you rant this on rcgroups where it was...

Why dont you rant this on rcgroups where it was originally started?:confused:
Forum: Foamies
01-17-2013, 10:01 PM
Replies: 6
Views: 1,180
Posted By dopey190

And Im guessing these 9x6 props from the brushed...

And Im guessing these 9x6 props from the brushed motor need to be drilled to fit? Or just buy the props that fit correctly?
Forum: Foamies
01-17-2013, 08:29 PM
Replies: 6
Views: 1,180
Posted By dopey190

Need brushless help again

How in the world does this setup work, I cannot for the life of me figure out how this stays on the motor shaft securely. ????
Theres no place to tighten down the adapter, I know this is probably...
Forum: Foamies
01-16-2013, 11:31 PM
Replies: 8
Views: 1,433
Posted By dopey190

Thanks!

Thanks!
Forum: Foamies
01-16-2013, 11:25 PM
Replies: 8
Views: 1,433
Posted By dopey190

Ok got that now, the million dollar question is ...

Ok got that now, the million dollar question is which prop?
Forum: Foamies
01-16-2013, 11:13 PM
Replies: 8
Views: 1,433
Posted By dopey190

Not sure about the prop adapter? I have whatever...

Not sure about the prop adapter? I have whatever they gave me in the bag that it came with. Figure I would find the right prop and then figure out how to put it on. :confused:
Forum: Foamies
01-16-2013, 10:58 PM
Replies: 8
Views: 1,433
Posted By dopey190

Build Review Need prop help for Super Cub

Putting together an brushless upgrade and have been doing alot of reading and can not find an answer for the right prop. I put a 480 eflite, I have a couple of 9x6 props. But i think I would have to...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.05574 seconds with 7 queries