WattFlyer RC Electric Flight Forums - Discuss radio control eflight - Search Results

 
Search: Posts Made By: Meekomagic
Showing results 1 to 30 of 36
Search took 0.00 seconds.
Forum: ParkFlyers
04-01-2011, 09:06 PM
Replies: 1,344
Views: 302,737
Posted By Meekomagic

Nice job, it helps to be creative.......Mike

Nice job, it helps to be creative.......Mike
03-28-2011, 04:19 PM
Replies: 24
Views: 4,492
Posted By Meekomagic

Thank You Hank, very informative........Mike

Thank You Hank, very informative........Mike
03-28-2011, 01:42 AM
Replies: 24
Views: 4,492
Posted By Meekomagic

I can get the inner shaft out and like I said I...

I can get the inner shaft out and like I said I have an aluminum head. How do you get the shaft out of the head? Is it a force fit or what?
03-28-2011, 12:48 AM
Replies: 24
Views: 4,492
Posted By Meekomagic

Well here I am with the Blade CX results after...

Well here I am with the Blade CX results after changing many parts after getting up the nerve to start taking it apart. I started off changing the outter shaft and that didn't help. Then I changed...
03-16-2011, 01:39 AM
Replies: 24
Views: 4,492
Posted By Meekomagic

I followed your advice, I throttled up and had...

I followed your advice, I throttled up and had the lower blades rotating. Before doing this I replaced the otter shaft. With the lower blades rotating I could see that outer shaft wobbled a bit. So I...
03-14-2011, 03:12 AM
Replies: 24
Views: 4,492
Posted By Meekomagic

MY blade CX vibrates, I changed the outter shaft...

MY blade CX vibrates, I changed the outter shaft so far and no improvement. What's next to change?
Forum: Beginners
09-25-2010, 11:33 PM
Replies: 79
Views: 13,532
Posted By Meekomagic

Thanks for that extra picture.......Mike

Thanks for that extra picture.......Mike
Forum: Beginners
09-22-2010, 05:21 PM
Replies: 79
Views: 13,532
Posted By Meekomagic

BEAR-AvHistory...

BEAR-AvHistory (http://www.wattflyer.com/forums/member.php?u=30239) Thanks for answering a long time question about the replacement motor. That was a great idea for the motor mount but I have a...
Forum: Beginners
09-22-2010, 02:09 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

To anyone interested, my vertical stabilizer...

To anyone interested, my vertical stabilizer cracked a few times and I was able to repair it with Gorilla Glue which I purchased at Lowes. The Gorilla Glue is cheaper than the CA glue and it does a...
Forum: ParkFlyers
09-21-2010, 03:44 AM
Replies: 1,344
Views: 302,737
Posted By Meekomagic

Carlos, I belong to the RCACF club in Apopka, I...

Carlos, I belong to the RCACF club in Apopka, I am a new flyer and I have an instructor who is teaching me. I also have an Apprentice....Mike
Forum: ParkFlyers
09-21-2010, 03:37 AM
Replies: 1,344
Views: 302,737
Posted By Meekomagic

I live in Clermont, where do you...

I live in Clermont, where do you fly............Mike
Forum: ParkFlyers
09-17-2010, 01:35 AM
Replies: 1,344
Views: 302,737
Posted By Meekomagic

I hear you about supporting your local HS but...

I hear you about supporting your local HS but they probably making 4 or 500% on those batteries they sell you. I am a patient guy so I buy from HK and wait the 2 weeks for delivery. The batteries I...
Forum: ParkFlyers
09-16-2010, 12:35 AM
Replies: 1,344
Views: 302,737
Posted By Meekomagic

T-28 Out the box

Hi guys, Although I am a new flyer, I have a Slow Stick, an Apprentice and a T-28. I have flown the Apprentice many times with a buddy box and tanked 3 times which cost me a few bucks. In the mean...
Forum: Beginners
09-04-2010, 02:24 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Replacement motor for eflight apprentice

Has anyone ordered a replacement motor for the Eflight Apprentice from either of these two sites?
http://www.hobbycity.com/hobbyking/store/uh_index.asp...
Forum: ParkFlyers
09-03-2010, 02:10 AM
Replies: 1,344
Views: 302,737
Posted By Meekomagic

I received my new PNP T-28 today, I am now...

I received my new PNP T-28 today, I am now waiting for that $15 6 channel receiver and 2 2200mah lipo's I purchased from Hobby King for a song......I am looking to purchase another motor and prop...
Forum: Beginners
08-22-2010, 10:50 PM
Replies: 79
Views: 13,532
Posted By Meekomagic

Has anyone purchased props from www.HobbyKing.com...

Has anyone purchased props from www.HobbyKing.com (http://www.HobbyKing.com) for the Apprentice and if you did I need the part number.................Mike
Forum: Beginners
08-12-2010, 01:06 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Took the Apprentice out for her sixth flight and...

Took the Apprentice out for her sixth flight and my instructor noticed the vertical stabalizer rocking back and forth in flight. We brought the plane in and the foam on the vertical stabalizer broke...
Forum: Beginners
08-10-2010, 08:55 PM
Replies: 79
Views: 13,532
Posted By Meekomagic

I found two good sites for r/c parts can anyone...

I found two good sites for r/c parts can anyone help me to find a replacement out runner motor for the Apprentice?



http://www.hobbycity.com/hobbyking/store/uh_index.asp...
Forum: Beginners
08-10-2010, 08:48 PM
Replies: 79
Views: 13,532
Posted By Meekomagic

I am also a new flyer, i have flown my Apprentice...

I am also a new flyer, i have flown my Apprentice with an instructor 5 times with one slight crash. I bent the outer casing of the motor but was able to straighten it out with a pair of channel...
Forum: Beginners
07-14-2010, 11:58 PM
Replies: 79
Views: 13,532
Posted By Meekomagic

Can I use a 3300 mah battery on the Apprentice?

Can I use a 3300 mah battery on the Apprentice?
Forum: Beginners
06-30-2010, 01:43 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Hello All, If I were to install 2 1/2" wheels on...

Hello All, If I were to install 2 1/2" wheels on the Apprentice, would I have to put one on the nose wheel also?
Does anyone have a Part Number for the 2 1/2 " wheels?.......Thanks Mike
Forum: Beginners
06-03-2010, 03:19 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Well the Apprentice arrived yesterday, I just...

Well the Apprentice arrived yesterday, I just finished epoxying the wing halfs and I will be ready to go soon. The only thing I was dissapointed with is no ac charger. Do I need a 12v power supply to...
Forum: Beginners
06-01-2010, 01:01 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

P. S. The Apprentice should arrive tomorrow, I am...

P. S. The Apprentice should arrive tomorrow, I am excited. I have a question about what should I double up on as far as parts are concerned to have on hand at the field.
Props
Extra...
Forum: Beginners
06-01-2010, 12:47 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

That Battery is only 16.79 at Hobby King. I am a...

That Battery is only 16.79 at Hobby King. I am a firm believer of you get what you pay for................
Forum: Beginners
06-01-2010, 12:45 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Can I use this Li-Po in the Apprentice? Spec. ...

Can I use this Li-Po in the Apprentice?
Spec.
Minimum Capacity: 3000mAh
Configuration: 3S1P / 11.1v / 3Cell
Constant Discharge: 20C
Peak Discharge (10sec): 30C
Pack Weight: 260g
Pack Size: 137...
Forum: Beginners
05-30-2010, 04:24 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

So I just spent $300 for the Apprentice. I just...

So I just spent $300 for the Apprentice. I just was looking on line for an extra battery. The batteries I found are $80, this hobby is for sure going to take me to the poor house. Where can I...
Forum: Beginners
05-30-2010, 03:01 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Rockin Robbins, This looks good, it's portable...

Rockin Robbins, This looks good, it's portable and a no brainer...DThanks
Forum: Beginners
05-29-2010, 03:55 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

I am also a new kid on the block expecting the...

I am also a new kid on the block expecting the Apprentice, it should arrive this Tuesday coming. I have a G4 simulator but I can't seem to have much luck flying. I just joined the AMA and I am going...
Forum: Beginners
05-29-2010, 03:16 AM
Replies: 79
Views: 13,532
Posted By Meekomagic

Bierchef, You explained how to make a cog jig but...

Bierchef, You explained how to make a cog jig but I don't fully understand your explanation. I have a 3/4 inch thick board 12" x 4". Do I find the center of the 12" and then measure 3" from that...
Forum: ParkFlyers
05-22-2010, 04:45 AM
Replies: 615
Views: 136,536
Posted By Meekomagic

Thanks for the info Bill, if I have to buy a new...

Thanks for the info Bill, if I have to buy a new motor for the SS what do you suggest and do I need anything else to go with the motor?..............Mike
Showing results 1 to 30 of 36
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.06475 seconds with 7 queries