Search: Posts Made By: jkaven
Showing results 1 to 13 of 13
Search took 0.00 seconds.
Forum: ParkFlyers
08-13-2009, 05:12 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

Last week I think. I didn't mention it at the...

Last week I think. I didn't mention it at the time because I was still mourning. :Q

So I'm up to a total of three crashes this summer. My Stryker, GeeBee and T-28. You don't feel that bad after...
Forum: ParkFlyers
08-13-2009, 04:07 AM
Replies: 1,344
Views: 290,415
Posted By jkaven

I need to glue my T-28 back together. The 35-42...

I need to glue my T-28 back together. The 35-42 is a strong crazy motor, but the plane can sure get away from you in a hurry. ;-)
Forum: ParkFlyers
07-28-2009, 02:33 AM
Replies: 1,344
Views: 290,415
Posted By jkaven

I land and take off on some really rough grass....

I land and take off on some really rough grass. It's a bit tricky at first compared to blacktop, but you should be able to do it.
Forum: ParkFlyers
07-27-2009, 07:43 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

Yeah the screws that hold the cross-plate to the...

Yeah the screws that hold the cross-plate to the motor. I made sure the longer screws aren't touching anything. Hopefully all goes well.
Forum: ParkFlyers
07-27-2009, 05:02 AM
Replies: 1,344
Views: 290,415
Posted By jkaven

I need to double check. I may not be doing it...

I need to double check. I may not be doing it right. I have a finger balancer from headsuprc. It's an EMP prop.

I used the screws that came with the turnigy. I looked at the screws that came with...
Forum: ParkFlyers
07-26-2009, 11:26 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

I ordered that 35-30 mount. I had a problem with...

I ordered that 35-30 mount. I had a problem with the motor screws coming loose. I read loctite will eat plastic, so a metal mount seems like a good idea.
Forum: ParkFlyers
07-26-2009, 10:41 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

Oh.. the shaft is the same size but the prop...

Oh.. the shaft is the same size but the prop adapter is bigger?

Yeah.. sorry there are clearance issues. I cut out the fake radial motor out of the T-28. I kind of like it better that way.

I...
Forum: ParkFlyers
07-26-2009, 07:35 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

I made a hinge for my stryker canopy. I used the...

I made a hinge for my stryker canopy. I used the mylar (I think that's what it is) from an old floppy disk. It's strong and flexible.
Forum: ParkFlyers
07-26-2009, 05:20 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

The T-28 prop shaft is larger than the Turnigy so...

The T-28 prop shaft is larger than the Turnigy so the stock props don't fit. If you buy a prop like APC they usually come with little rings to help you fit the prop to the shaft. That's what I'm...
Forum: ParkFlyers
07-26-2009, 05:08 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

I added 4 pairs of magnets with hot glue and...

I added 4 pairs of magnets with hot glue and glued the original magnet. I did the magnets on the fuselage first then set a servo screw on a couple magnets. Then I pushed down the cockpit. The screws...
Forum: ParkFlyers
07-25-2009, 11:52 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

Woo.. had a good flight with the new motor. Very...

Woo.. had a good flight with the new motor. Very fast. Due to high winds I couldn't do too much but I did some high speed laps. I do have to find a new test pilot though as the one I had bailed out...
Forum: ParkFlyers
07-25-2009, 06:02 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

I'm taking her out today with the sk 35-42 12...

I'm taking her out today with the sk 35-42 12 with a TGS 10x7E prop on 3s 2200.
Forum: ParkFlyers
04-26-2009, 10:01 PM
Replies: 1,344
Views: 290,415
Posted By jkaven

That is completely awesome!

That is completely awesome!
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.04576 seconds with 7 queries