thepiper92's Profile Picture

thepiper92 thepiper92 is offline

Warbird Fanatic

Visitor Messages

Showing Visitor Messages 1 to 10 of 12
  1. thepiper92
    04-19-2014 09:53 PM
    When you get into more complex builds you'll find you end up doing anything that just works, including different material and things that aren't even on plans
  2. time bandit
    04-19-2014 09:38 PM
    Thanks for the help. I was leaning that way but wanted to be sure before I put the glue to it. Never hurts to ask!!
  3. thepiper92
    04-19-2014 09:25 PM
    I looked at your build, match up the halves with the stab. That little spacing in the middle is the dowel place. Dab some glue on the halves, put in dowel and you can use the stab itself to line everything up.
  4. thepiper92
    04-19-2014 09:21 PM
    http://www.wattflyer.com/forums/showthread.php?t=72994

    That's the build, may not help a lot
  5. thepiper92
    04-19-2014 09:04 PM
    A slot going lengthwise down each half? That's not a bad thing, more surface area for glue. Just have to make sure you sand rounded or a v'ed center hinge, but typical on elevators the area is skinny so it ends up rounded.
  6. time bandit
    04-19-2014 07:46 PM
    Where do I find your P51 build at?
  7. time bandit
    04-19-2014 07:33 PM
    There is a slot already cut into the two elevator halves for the dowel. The instructions say to attach the elevators with a piece of 3/16th inch dowel. I just read it on the online fuse manual and it's the same as the one in my kit. I will check out your P51 build also. Thanks.
  8. thepiper92
    04-19-2014 06:38 PM
    My p51 build may be of some help
  9. thepiper92
    04-19-2014 06:32 PM
    I have not built the EVA, but it sounds the same as the P51. Lay the elevator halves on plans, and glue dowel across halves, so that the dowel is in between the elevator and the horizontal stab end. The dowel is the pivoting area. Do not notch the areas so the dowel sits in the elevator, just glue on surface, unless you plane to sand the edge of the elevator round to match the roundness of the dowel. This is, however, what I did on my P47, but on the P51 the dowel made the round area for pivoting
  10. time bandit
    04-19-2014 05:46 PM
    Hey there I have a question for you. Have you built the EVA sport from Mountain Models? If so How did you glue the 3/16 dowel piece to the elevators? I'm not sure If I lay the elevators flat and glue the round stock in or if I'm supposed to center the elevators on the round stock. Thanks for your time.

About Me

  • About thepiper92
    Location
    Winnipeg, Canada
    Interests
    Rc Planes, Rc Cars, Music (Bagpipes, Saxophone), History,
    Occupation
    Cashier, Student
    Favorite Pet(s)
    Dogs

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 06-17-2015 10:38 PM
  • Join Date: 11-21-2013
  • Referrals: 0

Friends

Showing Friends 1 to 6 of 6

iTrader

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.05921 seconds with 24 queries